optionrefi.com

Home > Hard Drive > Problem With XP Recognizing DVD & CD Drive In Master Slave

Problem With XP Recognizing DVD & CD Drive In Master Slave

Contents

I want to say Thank YOU!!! Read the partition posts, and figure I would need to "ghost" the OS, or would a clean install be better and ghost the rest of the programs? Another jumper setting, which you can use if you have an 80-conductor ribbon cable, is Cable Select. 80-conductor cables can be identified by their much finer wires compared to 40-conductor cables To format the drive in Windows 2000 or XP, right-click on My Computer and go to "Manage". Check This Out

My problem is that it thinks the "C" drive is the main drive & when I try to update my windows or drivers, it is not giving me the option to I can pull it out by just removing 1 screw. During a fresh install, Windows XP tests the ATA interfaces and the connected devices to determine DMA compatibility. Especially from WinXP 32bit to Vista 64bit.

How To Connect Ide Hard Drive To Sata Motherboard

When I first purchased the PC it came with a CD-ROM drive and Windows XP Professional pre-installed. Cant do nothing else. The ribbon cable is usually quite easy to remove. Optical drives are inexpensive.

The standard Windows format command is used with hard disks and standard floppy disks, while Zip, Superdisk, and other types of removable and optical media are usually formatted with a proprietary I'm just wondering about the jumper, I've had hard drives that didnt detect because the jumper was on 'Cable Select' and not 'Slave' Could be a long shot, but what about Improve speed at all? Ide Hard Drive Jumper Settings Preview post Submit post Cancel post You are reporting the following post: Mixing SATA and IDE drives in a system?

Thanks Reply Hans says: November 29, 2008 at 11:38 am Great Article. You've established that it is getting power to the driver, but not the information. The power supply of the enclosure that is, not the drive. http://xphelpandsupport.mvps.org/how_do_i_get_windows_to_recognis.htm Take Action It's time to speak out for your right to repair Dear Nebraskans, This year, the people of Nebraskans have a chance to guarantee their right to repair their equipment—like

It uses jargon from start to finish, leaving someone who is new to computers dumbfounded. How To Make Ide Boot Instead Of Sata Cables can be installed incorrectly, the system BIOS might not recognize the drive, the drive's media could be incorrectly formatted or even defective. How do I get my computer to recognize it. Would that make a difference?

Sata And Ide Hard Drives Together

Tell them that you believe repair should be fair, affordable, and accessible. https://www.cnet.com/forums/discussions/mixing-sata-and-ide-drives-in-a-system-115142/ thanks, Spiv Reply israel says: March 3, 2008 at 12:59 am ------HELP PLEASE----- i am putting a unpartioned hard drive in my computer as my slave hard drive. How To Connect Ide Hard Drive To Sata Motherboard Whereas an external device is usually a simple matter of connecting a cable or two and ensuring the device has power. Ide And Sata Drives In Same Computer For more information, you can read the Microsoft support article Optical drives do not work as expected after you upgrade a computer to Windows Vista (in English).

Install the updates according to the instructions on the download page. his comment is here The drive should work correctly once it has been enabled. Once again, in the BIOS menu, you should see the CD/DVD drive details displayed under the Secondary IDE Master or Slave sub menu. After boot windows xp/operating system on HD SATA, i re-activate IDE HDs and after backup data, repartitioned like i want. 5. Motherboard With Ide And Sata Ports

No luck anywhere. 07-29-2004, 08:11 AM #4 mlarson Registered Member Join Date: Jul 2004 Posts: 7 OS: XP TDK Mulitformat 4x burner 440N All window updates are installed. Your computer should see and read your drivejust fine. John Barnett. this contact form The disc drive should now be recognized by your recording software.

Reply Rivers says: August 4, 2007 at 2:07 am I installed a extra hard drive in my pc and would like to completely wipe all data from it. What Are The Two Goals When Implementing A Raid Solution Use a file to grind down any sharp burrs that remain, ensuring that no filings remain inside the case on the motherboard where they can cause havoc. Windows will now scan for any new hardware and should pick up your CD/DVD drive.

The process varies based on the specific type of device, but the first step always involves the physical installation and cabling of the drive.

Assigning the highest available drive letter, Z, to the optical drive prevents Windows from ever altering that drive letter. now I can install an OS to my blank 80GB HDD." At least that was what I thought. Don't force it. How Many Hard Drives Can Be Connected To A Single Ide Cable Thank you so much for this information… I was going in to my computer and to no avail didnt see the second hard drive.

Took me hours of wading through other websites of gobbledygook to get nowhere. PCMech has long been a fan of Acronis True Image. Right-click the drive name and select Enable. http://optionrefi.com/hard-drive/xp-drive-will-not-boot-after-vista-install-on-new-drive.php the IDE cable I purchased is a flat cable; however, towards the blue end it's squeezed into a black oval-ish rubber-like tube.

I shutdown my computer, unplugged the power cable and disconnected the DVD drive, then I reconnected it and made sure everything was securely connected. I'll post a reply with the results. Either way we try to address the problem here. Well, thing is, I have 900GB of data on the drive that I cannot lose.

Most cables are keyed to the connector so they only go in one way; if the cable isn't going in, try flipping it over. I cloned my 90GB IDE onto a 250GB IDE using a bootable HD Cloning CD. It’s yours. System runs windows xp.If I look at the drives in computer management, both drives show up as healthy, but one is labeled "system" and the other is labeled "page files" There